PavedEarth CR-Z
  • Uncategorized
  • DIY
  • Photos and Videos
  • Aftermarket
  • OEM
  • Photoshops
  • Wheels and fitment
  • Suspension and handling
  • Interior
  • Exterior
  • Engine
  • News
  • Editor's Picks
  • Product
  • Reviews
  • RSS Feed
  • Facebook

Archive for March, 2011

  •   Awaiting a soccer practice that apparently wasn’t actually going to happen, it seemed like a good time to break out the camera and snap some shots since things were […]

    Honda CR-Z Photoshoot One

    Posted on March 31, 2011 | 1 Comment
      Awaiting a soccer practice that apparently wasn’t actually going to happen, it seemed like a good time to break out the camera and snap some shots since things were […]

    Continue Reading...

  • Disclaimer: I take NO responsibility for any damages, induced costs or accidents that may occur when using the DIY Articles. Use the articles at your own risk, knowing that they […]

    Honda CR-Z rear wiper delete DIY

    Posted on March 30, 2011 | 4 Comments
    Disclaimer: I take NO responsibility for any damages, induced costs or accidents that may occur when using the DIY Articles. Use the articles at your own risk, knowing that they […]

    Continue Reading...

  • ARK Design’s Accelerator Throttle Curve Controller (ATCC) is an add-on electronics unit that modifies your vehicle’s drive-by-wire throttle signal output and allows you to modify acceleration response to your liking. […]

    ARK Design ATCC for CR-Z

    Posted on March 29, 2011 | 2 Comments
    ARK Design’s Accelerator Throttle Curve Controller (ATCC) is an add-on electronics unit that modifies your vehicle’s drive-by-wire throttle signal output and allows you to modify acceleration response to your liking. […]

    Continue Reading...

  • Finally the rain has stopped long enough to jack the car up and get the exhaust and diffuser from Noblesse mounted. Install instructions were in Japanese, and for the most […]

    Noblesse diffuser and dual port exhaust

    Posted on March 28, 2011 | 3 Comments
    Finally the rain has stopped long enough to jack the car up and get the exhaust and diffuser from Noblesse mounted. Install instructions were in Japanese, and for the most […]

    Continue Reading...

  •   Installation was pretty simple. The majority of the installation can be done away from the vehicle and then just put in place. To be noted that pre-attaching the aluminum […]

    HKS Racing Suction Reloaded intake

    Posted on March 27, 2011 | 1 Comment
      Installation was pretty simple. The majority of the installation can be done away from the vehicle and then just put in place. To be noted that pre-attaching the aluminum […]

    Continue Reading...

  •   Thanx to Jason at Bulletproof Automotive the Noblesse parts have arrived! Now being tortured by weather (stupid rain) and not being able to install. NOTE: The diffuser does not […]

    Noblesse CR-Z parts landed!

    Posted on March 27, 2011 | 1 Comment
      Thanx to Jason at Bulletproof Automotive the Noblesse parts have arrived! Now being tortured by weather (stupid rain) and not being able to install. NOTE: The diffuser does not […]

    Continue Reading...

  • Finally was able to finish and reassemble the interior of the CR-Z. All of the legacy grey interior is now gone and replaced by black and red leather seats, black […]

    Honda CR-Z interior

    Posted on March 27, 2011 | 10 Comments
    Finally was able to finish and reassemble the interior of the CR-Z. All of the legacy grey interior is now gone and replaced by black and red leather seats, black […]

    Continue Reading...

  • Google Search
  • Advertisement
  • CR-Z @ Flickr
  • Advertisement
  • Automotive
    • 3d Carbon Works
    • CRZ Forum CRZ Forum
  • Blogroll
    • 600x League 600x League

About Arras WordPress Theme

Copyright Marc Kodama. All Rights Reserved.

 

Loading Comments...